Depth: 30 metres | Length: 85 metres | Cargo: Coal The wreck has been salvaged and decayed close to the 34m seabed, so our tour begins at the highest point of the wreck by the boilers (1), the tops of which come to just shy of 30m. Staying on the starboard side of the ship, a cargo winch that would have served the aft holds is broken with the base upside-down, then the spindles spread next to the base (5). The sides of the hull have fallen outward to the seabed, leaving just a hint of where the original outline of the hull rises.
Syracusa 30m 1879-1897
The port boiler is pretty much intact, while the starboard boiler is opened up to display a tangle of boiler tubing.
Just aft of the starboard boiler, a small single-cylinder steam engine would have driven a pump (2).
The top of the main triple-expansion steam engine (3) has fallen to starboard, leaving the connecting rods twisted over and the port side of the supporting struts for the engine remaining upright.
Behind the engine, the crankshaft is still connected to the thrust-bearing (4), with the propeller-shaft emerging from the remains of the engine-room bulkhead and continuing sternwards.
The hull soon begins to narrow for the stern, with a pair of bollards fallen from a long-decayed but still upright deck just inside the hull. Coal remaining from the cargo is scattered nearby.The hull ends with a break in the propeller-shaft (6).
A few metres off the stern, and a little to starboard, lies the top of the rudder-post and the steering mechanism (7), an interesting dustbin-shaped casing that would have contained the gearing to turn the rudder-shaft through rotation of a horizontal steering-shaft.
A little further out, and off to port, is the tail section of the keel, with the last section of propeller-shaft, the stern gland and the propeller (8). Behind this is the rudder – perfectly positioned relative to the propeller, but with the top of the shaft bent over by almost 90°.
This suggests that the Syracusa went down stern-first with the tide running, so that the rudder and propeller caught on the seabed and were wrenched from the ship as it settled with the tide.
Now, following the propeller-shaft forwards, count the bearing blocks that support it above the keel. Just after the third block forwards from the stern, and partly hidden beneath the shaft, is a large ring spanner (9), sized to fit the big nut that holds the propeller on the end of the shaft.
With such a spanner carried, I would also have expected the Syracusa to have been carrying a spare propeller, but I failed to find it. Perhaps it is partly buried in debris somewhere, perhaps it was salvaged, or perhaps the Syracusa was already running on its spare.
The port side of the hold contains a further scattering of coal from the cargo. Then, as we near the engine-room bulkhead, the port side of the hull remains intact and rises to main deck level (10).
This continues past the boilers, then drops to the seabed again where the side of the hull has fallen outwards.
A pair of bulkheads crossing the wreck here marks the bunker space, where the coal for fuelling the ship’s boilers would have been held. In the middle of this space and towards the forward bulkhead is the helm and steering-engine (11), fallen from the wheelhouse that would have been above this part of the ship.
Forward of this bulkhead and along the hold, a pair of winches (12) rest upright on either side of the mast-foot that stands from the keel. Off to the port side, the side of the hull is again intact, with even a scrap of the main deck supported by it, though drooping slightly.
Continuing along the forward hold, the anchor-winch (13) has fallen to rest across the keel. The starboard side of the bow has fallen inwards (14), while the port side of the bow has fallen outward to rest on the seabed.
Right at the tip of the bow, it is broken down almost to the keel (15). A pair of bollards (16) stand upright on the coarse granite sand a couple of metres out to port.
A similar distance off to starboard is a small derrick (17). This would originally have been located in the centre of the bow deck, and used for lifting anchors onto the deck after the anchor-winch had raised them.
Our route back to the boilers and the shotline follows the broken starboard side of the hull (18). Just before arriving back
at the boilers, a fallen plate has a small valve wheel on it (19). Any time remaining before ascending the shotline can be spent looking for conger eels among the tubes of the starboard boiler.
Depth: 30 metres | Length: 85 metres | Cargo: Coal
The wreck has been salvaged and decayed close to the 34m seabed, so our tour begins at the highest point of the wreck by the boilers (1), the tops of which come to just shy of 30m.
Staying on the starboard side of the ship, a cargo winch that would have served the aft holds is broken with the base upside-down, then the spindles spread next to the base (5). The sides of the hull have fallen outward to the seabed, leaving just a hint of where the original outline of the hull rises.